How to Sew a Bound Seam with a Sewing Machine?

Bias-bound seams are an excellent method to finish your sewing. Bound seams shield the raw edge of seams and provide an extra splash of color. The bound seam is called Hong Kong Finish.

Although they’re not a lot time-consuming, however, the result is worth it! There are many methods to sew bound seams.

Double-folded bias tape is utilized in bias-bound seams to complete the seam edges. It is possible to use the bias tape individually (a press-open seam) to both seam allowances or in one go (a seam that has been pressed on one end) to seam allowances. If you do this, be aware of the amount of fabric you use since the seam could get too thick.

Today, I’ll share with you a method I love the most. Let’s do it.

Tools You are Going to Need:

• The fabric you would like to utilize.
• The appropriate Needle or thread of the chosen fabric
• Standard foot
• Binder’s foot
• Applique scissor, or any other scissor with a sharp edge
• Pins
• bias binding or bias strips
• Ironing Board and iron (As pressing is an essential element of the finishing techniques).

(You can buy these ones with cheaper price here)

How to sew a Bound Seam using a Sewing Machine?

Step 1:

Make sure you are ready to sew your seam using the seam allowance of your fingers by pressing the seam allowance open just a bit. These seam allowances need to be slightly higher. This way, it will make it slightly easier to continue the process.

Step 2:

Make some bias binding (also known as bias strips). They can be made yourself or buy them pre-made from shops.

Step 3:

Use the seam allowance that you’ve prepared and place the bias strip on the upper right side of the other by lining up to the rough edges. Then, pin the binding to the seam allowance to sew an allowance for seams to join the binding.

The next step is to move all your fabric to the left before you begin sewing. Ensure you don’t accidentally sew through the right portion of your fabric.

Step 4:

Prepare yourself to create an elongated seam allowance. The edge of the presser foot is a guide. Make a straight stitch to fix the binding to the seam allowance.

If you’ve reached the bottom, you only need to trim off the excess piece from the bias strips.

Step 5:

The next step is to use an iron to press the seam. The finger press is not efficient because it will become flexible and bouncy.

Step 6:

The following step is trimming the seam allowance. Leave 1/8″ on the seam allowance, splitting the wide seam into two halves.

Step 7:

Now fold the binding over and then stitch it back. Pin the binding in place. It’s a nice idea to secure the binding near the seam, then flip it over to ensure that you have that binding on the opposite side.

Step 8:

You are now ready to return it to your sewing machine. The seam allowance should be placed under the foot of the presser. Before you begin, you can use a hand wheel to lower the Needle to let you discern where the Needle is likely to go.

It will fall into the seam or just a bit away from the seam. Now that you know where it will be, you’re in a position to stitch.

Step 9:

When you are near the finish line, ensure that the binding isn’t being pulled out and tucked beneath since it can move since it’s elastic. Then pull it out, and you will have your seam bound.

When you’re done, you can transfer the garment to iron and press it until it looks good and flat.

More Helpful Tips For Sewing a Bound Seam:

1. If you have difficulty stitching your “ditch,” or there isn’t any special foot available, try stitching the edges of your seam. You could attempt a zig-zag stitch to create a beautiful finish.
2. Premade, store-bought double-sided bias tape is more suitable to sew as it is created more precisely.
3. If you’re planning to create your double-fold bias tape, make sure you use an extra long piece of fabric to reduce the seams.
4. If you’re using tape from a store, ensure the tape’s narrow edge is to one side.
5. It is best to use lighter fabrics for your bias tape to reduce the bulk of seams.
6. This technique is common for a garment factory and can also be employed for accessories and home decoration. If you’re looking to make the corner, you’ll learn how to cut corners using binding seams online.
7. Bound seams can also be applied to the outside edge of the fabric, like around the neckline or on top of a bag that is not lined or sleeves edges on an item.
8. If you’re looking to make something reversible, it is necessary to use a bound seam. In this situation, French seams won’t work.
9. It is possible to avoid an indentation to the left side of your dress when you press the seam to close by placing a small portion made of brown paper between two layers of fabric.
10. If you plan to use a print or a bold color fabric to tie it, you must ensure that it’s not also. Otherwise, the coloring of the binding could be evident from the back of the fabric.
11. If you want to make your stitch line more uniform, use the edge stitch foot.
12. You should think about the sequence of the pieces you will need to build the sewing piece.
13. It is recommended to try binding a strip of different widths on scraps that are sewn with a precise seam allowance before starting the bound seam method.

See Also:

• Best Sewing Machine for Advanced Sewers
• Best Sewing Machine for Buttonholes
• Best Heavy Duty Sewing Machine for Beginners
• Best Serger Sewing Machine for Beginners
• Most Reliable Home Sewing Machines
• Best Portable Sewing Machine For Beginners
• Brother se400 vs Brother se600
• Juki 2000qi Review
• Singer Quantum Stylist 9960 Reviews
• Singer 9960 Sewing Machine Reviews
• Singer 9960 vs 9985
• Brother PQ1500sl Reviews
• Juki tl 2010q Reviews
• Common Sewing Machine Problems
• How to Use an Electric Sewing Machine for Beginners